**Compressive strength of concrete cube test** provides an idea about all the characteristics of concrete. By this single test one judge that whether Concreting has been done properly or not. Concrete compressive strength for general construction varies from 15 MPa (2200 psi) to 30 MPa (4400 psi) and higher in commercial and industrial structures.

Compressive strength of concrete depends on many factors such as water-cement ratio, cement strength, quality of concrete material, quality control during production of concrete etc.

**Test for compressive strength** is carried out either on cube or cylinder. Various standard codes recommends concrete cylinder or concrete cube as the standard specimen for the test. American Society for Testing Materials ASTM C39/C39M provides Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens.

**Compressive Strength Definition**

**Compressive strength** is the ability of material or structure to carry the loads on its surface without any crack or deflection. A material under compression tends to reduce the size, while in tension, size elongates.

**Compressive Strength Formula**

**Compressive strength formula** for any material is the load applied at the point of failure to the cross-section area of the face on which load was applied.

**Compressive Strength = Load / Cross-sectional Area**

**Procedure: Compressive Strength Test of Concrete Cubes**

**For cube test two types of specimens** either cubes of 15cm X 15cm X 15cm or 10cm X 10cm x 10cm depending upon the size of aggregate are used. For most of the works cubical moulds of size 15cm x 15cm x 15cm are commonly used.

**concrete cube mould**

This concrete is poured in the mould and tempered properly so as not to have any voids. After 24 hours these moulds are removed and test specimens are put in water for curing. The top surface of these specimen should be made even and smooth. This is done by putting cement paste and spreading smoothly on whole area of specimen.

These specimens are tested by compression testing machine after 7 days curing or 28 days curing. Load should be applied gradually at the rate of 140 kg/cm2 per minute till the Specimens fails. Load at the failure divided by area of specimen gives the compressive strength of concrete.

**Compressive Strength Test on Concrete Cube**

Following are the procedure for testing Compressive strength of Concrete Cubes

Apparatus for Concrete Cube Test

Compression testing machine

Preparation of Concrete Cube Specimen

The proportion and material for making these test specimens are from the same concrete used in the field.

Specimen

6 cubes of 15 cm size Mix. M15 or above

Mixing of Concrete for Cube Test

Mix the concrete either by hand or in a laboratory batch mixer

**Hand Mixing**

Mix the cement and fine aggregate on a water tight none-absorbent platform until the mixture is thoroughly blended and is of uniform color

Add the coarse aggregate and mix with cement and fine aggregate until the coarse aggregate is uniformly distributed throughout the batch

Add water and mix it until the concrete appears to be homogeneous and of the desired consistency

Sampling of Cubes for Test

Clean the mounds and apply oil

Fill the concrete in the molds in layers approximately 5 cm thick

Compact each layer with not less than 35 strokes per layer using a tamping rod (steel bar 16mm diameter and 60cm long, bullet pointed at lower end)

Level the top surface and smoothen it with a trowel

**Curing of Cubes**

The test specimens are stored in moist air for 24 hours and after this period the specimens are marked and removed from the molds and kept submerged in clear fresh water until taken out prior to test.

**Precautions for Tests**

The water for curing should be tested every 7 days and the temperature of water must be at 27+-2oC.

Procedure for Concrete Cube Test

Remove the specimen from water after specified curing time and wipe out excess water from the surface.

Take the dimension of the specimen to the nearest 0.2m

Clean the bearing surface of the testing machine

Place the specimen in the machine in such a manner that the load shall be applied to the opposite sides of the cube cast.

Align the specimen centrally on the base plate of the machine.

Rotate the movable portion gently by hand so that it touches the top surface of the specimen.

Apply the load gradually without shock and continuously at the rate of 140 kg/cm2/minute till the specimen fails

Record the maximum load and note any unusual features in the type of failure.

**Note:**

Minimum three specimens should be tested at each selected age. If strength of any specimen varies by more than 15 percent of average strength, results of such specimen should be rejected. Average of three specimens gives the crushing strength of concrete. The strength requirements of concrete.

**Calculations of Compressive Strength**

**Size of the cube =15cmx15cmx15cm**

Area of the specimen (calculated from the mean size of the specimen )=225 cm2

Characteristic compressive strength(f ck)at 7 days =

Expected maximum load =fck x area x f.s

Range to be selected is …………………..

Similar calculation should be done for 28 day compressive strength

Maximum load applied =……….tones = ………….N

Compressive strength = (Load in N/ Area in mm2)=……………N/mm2

=……………………….N/mm2

Reports of Cube Test

Identification mark

**Date of test**

Age of specimen

Curing conditions, including date of manufacture of specimen

Appearance of fractured faces of concrete and the type of fracture if they are unusual

Results of Concrete Cube Test

Average compressive strength of the concrete cube = ………….N/ mm2 (at 7 days)

Average compressive strength of the concrete cube =………. N/mm2 (at 28 days)